The computer is on, the fans are running, and the monitor shows nothing but a “No Signal” box before it drifts into power saving. The good news: that message means the monitor itself has power and is waiting for a picture. The cause may be the computer, cable, monitor input or another hardware fault.
Quick answer: When a monitor says no signal, first select the right input (HDMI, DisplayPort or USB-C) in the monitor’s menu, then reseat the video cable at both ends and try another cable or port. Wake the computer with the mouse or keyboard. If your PC has a separate graphics card, plug the monitor into the card’s ports, not the motherboard’s. If the monitor shows its own self-test screen with the cable unplugged, its basic display works, so focus on the input, cable and computer.

This guide is part of our series on fixing TV and monitor screen problems.
What “No Signal” actually tells you
| What you see | What it usually means |
|---|---|
| “No Signal” or “No HDMI/DP Cable” box, power light on | The monitor has power but detects no video on the selected input |
| Message appears, then the monitor goes to power saving | No active video signal is reaching the monitor |
| Black screen with no message and no power light | Possible power or monitor hardware problem |
| Picture appears briefly during startup, then “No Signal” | A driver, resolution or graphics card issue on the computer |
1. Select the correct input
Most monitors have several inputs, and many don’t switch automatically. Press the monitor’s input or menu button (some models use a joystick under the bottom edge), open Input Source and choose the port your cable is actually plugged into, such as HDMI 1, HDMI 2 or DisplayPort. Dell lists this as the first check in its monitor troubleshooting guide.
2. Reseat or replace the cable
- Unplug the video cable at both ends and push it back in firmly.
- Inspect connectors for damage, debris or bent contacts. Release any DisplayPort locking tab before unplugging.
- Remove adapters, extension cables and docks for now, and connect the monitor directly.
- Try a different cable, or a different port on both the monitor and the computer.
- Using USB-C? Not every USB-C port supports video. Check that the computer’s port and the cable support display output.
3. Wake the computer and check the display mode
Move the mouse or press a key, since a sleeping computer sends no signal. On a Windows laptop, press Windows key + P and choose Duplicate or Extend. If the laptop is set to PC screen only, the external monitor gets nothing.
4. Use the graphics card’s ports
Desktop PCs with a separate graphics card have two sets of video ports. If the monitor is plugged into the motherboard’s ports near the top of the back panel, move the cable to the graphics card’s ports, which usually sit lower down on a horizontal bracket. When a graphics card is installed, the motherboard ports are often disabled.
5. Run the monitor’s self-test
Turn the monitor off, unplug the video cable and turn the monitor back on. Many monitors, including Dell models, then show a self-test or “no cable” screen. Dell says that if the self-test screen appears, the monitor is working. A visible self-test confirms basic display functionality but does not rule out a faulty video input. If nothing appears at all, the monitor may need service.
6. Test with another computer or device
Connect the monitor to a different laptop, game console or streaming device. If the monitor works with another device, the original computer or its connection is likely responsible, such as its graphics card, driver, settings or cable. If the second device also gets “No Signal” with a known-good cable, the monitor’s input port may be faulty.
7. Fix the computer side
- Power reset: follow your computer manufacturer’s power-reset instructions. On supported Dell computers, shut down, disconnect power and non-essential accessories, hold the power button for 15 to 20 seconds, reconnect power and restart.
- Graphics driver: if you can see Windows on another screen, update or roll back the display driver in Device Manager.
- Windows updates: install any pending updates and restart.
- Resolution or refresh rate too high: if the picture vanished right after you changed display settings, wait 15 seconds without clicking; Windows normally reverts the change automatically.
Spinning fans do not confirm a successful startup. Repeated beeps or diagnostic lights may indicate a hardware or POST failure rather than a monitor connection problem.
Seeing “No Signal” on a TV rather than a monitor? See how to fix HDMI no signal on a TV. If the picture is there but flickers, go to monitor screen flickering.
Frequently asked questions
Why is my PC turning on but not displaying on my monitor?
The monitor may be on the wrong input, plugged into the motherboard instead of the graphics card, or connected with a faulty cable. The computer may also be asleep or set to show its display somewhere else.
Why does HDMI say no signal when it’s connected?
A cable can be plugged in and still not carry video: the input may be wrong, the cable may be damaged, or the source device may be off or sending to another port.
Why does my monitor say no signal and then go to sleep?
Monitors enter power saving when they receive no video for a short time. Restoring the video signal normally wakes the monitor; some models may require manual input selection.
How do I know if the monitor or the computer is the problem?
Run the self-test with the cable unplugged and try the monitor with another device. If the monitor works with another device, the original computer or its connection is likely responsible.
Why does my laptop detect my monitor but show no signal?
Press Windows key + P and select Extend or Duplicate, check that the monitor is on the right input, try another cable, and press Windows key + Ctrl + Shift + B to reset the graphics driver, a shortcut described in Microsoft’s support guide.
How we researched this guide
This guide draws on Dell’s monitor troubleshooting guide and display support pages, reviewed on November 17, 2026. We did not test these steps on a device. Button names and menus vary by monitor brand and model.

Louis Mugan writes how-to and troubleshooting guides for EasyTechLife, covering Android phones, iPhones, laptops, Chromebooks, headphones and everyday software.
He aims to base each guide on official manufacturer documentation and support pages, and to link the sources so readers can check the steps for themselves. Questions or corrections? Use the contact page.


